The purpose of the present study was to examine effects of driver, vehicle, and environment characteristics on Collision Warning System (CWS) design. One hypothesis was made that the capability of collision avoidance would not be same among a driver, vehicle, and environment group with different characteristics. Accident analysis and quantitative analysis was used to examine this hypothesis in terms of ?risk? and ?safety margin? respectively. Rear-end collision had a stronger focus in the present study.

To design new and high tech products the engineers rely more and more on computer based simulations to investigate the properties and behavior for a component or system.To verify these computer based simulations the dynamic properties for the components of the drivetrain needs to be verified. Therefore measurements of the stiffness and vibrations for the rear axle has been performed. This report show how the measurements has been implemented and evaluated, along with some interesting results for the rear axles properties.The static stiffness for the drive shaft along with the axle-gear has been determined. It is found that the stiffness for the whole rear axle is near the stiffness for the drive shaft, which means that the drive shaft becomes the dominant component of the system and affects the rear axle stiffness the most. The measured stiffness of the driveshaft is close to its theoretical stiffness.The stiffness for solely the hypoid-gear have been calculated using the stiffness for the rear axle and driveshaft, and thus has a range for the stiffness of the hypoid gear been determined.The backlash for the whole rear axle and for some individual components has been determined, where the backlash between pinion and crown-wheel has negligible impact on the total backlash.Measurements of the crown-wheel and pinion movements have been conducted, where the direction of movement is consistent with the theoretical direction of the forces.The vibration measurements show that the vibrations are more severe at certain rotational speeds.

This thesis has been performed at Scania CV AB Technical Centre in Södertälje and its aim hasbeen to study the causes and effects of deformations in the interface between the rear axlehousing ADA1100 and the central gear house R780 during operation. Design changes that wouldincrease the sealing capability of the studied interface are also suggested. Finite element (FE)and CAD software have been the primary tools in this study.Finite element (FE) simulations are used in the industry to predict and develop engineeringdesigns. The main motive for FE simulations has traditionally been to identify weak spots in thedesign, regarding high tensions and large deformations.The FE model is an aggregation of submodels and interface models that represents the rear axlehousing, suspension, central gear, central gear housing, wheels, bolts and weldings, and theirinteractions. The submodels have different material properties and they are connected withcontact interface models.Boundary conditions are defined on the bushings in front of the rear axle and on the air bellowsbehind the rear axle.

Municipal safety work is an issue frequently discussed. The new legislation about accident prevention obeys the Swedish municipality to present an action program for accident prevention. In Borlänge municipality there has been no sanctioned proposal for a program. This report presents the problems found and gives proposals for improvements in the future safety work. The guiding words should be unambiguousness, able to control and not too complicated.

Driving simulators are a very important part of the research that is done at VTI. Enhancing the realism and creating a better driving experience in the simulators are very important and an ongoing work process for the engineers and researchers who work with the simulators. This project has been done as a part of this developing process and the purpose is to enhance the realism of the rear-view mirrors.Simulating realistic rear-view mirrors has been demanded, not only from the researchers at VTI, but also from car and truck manufacturers. To achieve a realistic mirror view a method to measure and parameterize real mirrors has been developed. The code for the existing graphics system has also been redone to be able to handle the new types of mirrors introduced..

The theme in this report has been how to benefit experience from accident investigations. The demand on the municipality to perform accidet investigations is relatively new, and maybe they aren?t clear what the demands means. This causes that there might be a problem to benefit experience from accident investigations, for improving the overall safety in the municipality. The main purpose of this report has been to clarify how experience from accident investigations, can be of benefit to society on a local level.

When performing a QRA you have to consider a number of accident scenarios. How many scenarios you choose often determines the time and resources needed to perform the QRA. The report investigates the possibility that a QRA can be performed using only a few representative scenarios. Further it presents a discussion on how these scenarios should be constructed..

In my degree project I have focused on how to make it easier for ambulance personnel to remove a motorcycle helmet after an accident. During my research I have interviewed ambulance personnel from different cities and a trauma surgeon to get a better understanding of how they work today and the problems they experience. Some of the problem areas are that you need a lot of force to remove the helmet, that the padding catches the ears and that the chin guard catches the face. Since ambulance personnel always assume that there is a neck injury after an accident, all these problems make it difficult to remove the helmet safely.The result is a motorcycle helmet with a focus on safe removal after an accident, to reduce the risk of worsening a neck injury. The solution suggested is that a small part of the back of the helmet is detachable, to make the opening larger.

The interaction between the driver, the car and the road is essential for the road safety. This case study focuses on the road condition and its effect regarding road safety issues. By studying and isolating the road condition aspect and its contributing role to the accident occurrence, the aim is to explore their relationship, as well as highlight the road parameters that are commonly associated with accident occurrence. This result will be used to develop and increase awareness of the impact of poor road alignment and poor road surface conditions on traffic safety, in order to prevent these accidents from occurring. The road parameters chosen for this study include side friction, cross slope and rut bottom cross slope, road texture, curvature, drainage gradient and rutting.The case study was limited to lv 360 in Va?sterbotten, where all accidents with an unclear cause of the accident were studied, between 2003 and 2012 were carefully studied and assessed based on the condition of the road at the time of the accident.

In my degree project I have focused on how to make it easier for ambulance personnel to remove a motorcycle helmet after an accident. During my research I have interviewed ambulance personnel from different cities and a trauma surgeon to get a better understanding of how they work today and the problems they experience. Some of the problem areas are that you need a lot of force to remove the helmet, that the padding catches the ears and that the chin guard catches the face. Since ambulance personnel always assume that there is a neck injury after an accident, all these problems make it difficult to remove the helmet safely.The result is a motorcycle helmet with a focus on safe removal after an accident, to reduce the risk of worsening a neck injury. The solution suggested is that a small part of the back of the helmet is detachable, to make the opening larger.

When farm animals are transported there are several factors that can affect their welfare. If the vehicle has an accident the welfare of the animals transported will probably be compromised. The aim of this study was to make a survey of accidents with animal transportation vehicles in Sweden. The survey included the number of accidents from January 2000 to May 2014, the cause of the accidents and how the animal welfare was affected by the accident. The authorities which were likely to have reports about accidents involving animal transports were contacted. There were no collected records about transportation accidents and the authorities referred to eachother for information.

In this thesis, a transparent model of the human head has been constructed which was filled with a substance that represented the brain. This model was later crash tested. This was done in order to examine how a transparent model of the human head can be constructed to generate accurate data from crash tests. It was also done in order to examine how impacts on the front of the head can deform the rear of the brain. When a head is decelerating, the brain moves forward inside the skull and may hit the front of the skull.

In this thesis, a transparent model of the human head has been constructed which was filled with a substance that represented the brain. This model was later crash tested. This was done in order to examine how a transparent model of the human head can be constructed to generate accurate data from crash tests. It was also done in order to examine how impacts on the front of the head can deform the rear of the brain. When a head is decelerating, the brain moves forward inside the skull and may hit the front of the skull.

In this thesis, a transparent model of the human head has been constructed which was filled with a substance that represented the brain. This model was later crash tested. This was done in order to examine how a transparent model of the human head can be constructed to generate accurate data from crash tests. It was also done in order to examine how impacts on the front of the head can deform the rear of the brain. When a head is decelerating, the brain moves forward inside the skull and may hit the front of the skull.

Human - Technology - Organization (HTO) is a well-established, general unifying concept in the Swedish Accident Investigation Authority (SHK) that represents an approach, knowledge and use of various tools regarding interactions between people, technology and organizational factors. The HTO-perspective is well described in literature but there are few studies on how SHKs staff experiences working according to this method in their investigations. The aim of this study was therefore to describe their HTO-perspective, examine how it is used in the investigations at SHK and describe the investigators experience of working with the HTO-perspective as well as the method's usefulness compared to old methods in accident investigations. A literature study has been conducted in the areas of HTO, Theory of planned behavior (TPB) and safety culture. TPB and safety culture are described in this paper since they highlight the different aspects of a HTO-perspective.